View HT27LC512_201534.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT27LC512 OTP CMOS 64Kx8-Bit EPROM
Features
* * *
*
* * * *
64Kx8-bit organization Single +3.3V power supply Programming voltage - VPP=12.2V0.2V - VCC=5.8V0.2V Low power consumption - Active: 15mA max. - Standby: 1A typ. Fast read access time: 120ns CMOS and TTL compatible I/O Commercial and industrial temperature range Fast programming algorithm
* * * * * * *
*
Read access time: -120ns Programming time 75s typ. High-reliability CMOS technology Latch-up immunity to 100mA from -1.0V to VCC+1.0V Two line control (OE & CE) Standard product identification code Package type - 28-pin DIP/SOP - 32-pin PLCC Commercial temperature ranges (0C to +70C)
General Description
The HT27LC512 chip family is a low-power, 512K bit, +3.3V electrically one-time programmable (O TP ) read-only memories (EPROM). Organized into 64K words with 8 bits per word, it features a fast single address location programming, typically at 75s per byte. Any byte can be accessed in less than 120ns with respect to Spec. This eliminates the need for WAIT states in high-performance microprocessor systems. The HT27LC512 has separate Output Enable (OE) and Chip Enable (CE) controls which eliminate bus contention issues.
Block Diagram
1
6th May '99
HT27LC512
Pin Assignment
Pin Description
Pin Name
A0~A15 DQ0~DQ7 CE OE/VPP NC
I/O/C/P
I I/O C C/P -- Address inputs Data inputs/outputs Chip enable
Description
Output enable/program voltage supply No connection
Absolute Maximum Ratings
Operation Temperature Commercial ...................................................................................0C to +70C Storage Temperature......................................................................................................... -65C to 125C Applied VCC Voltage with Respect to GND....................................................................... -0.6V to 7.0V Applied Voltage on Input Pin with Respect to GND ......................................................... -0.6V to 7.0V Applied Voltage on Output Pin with Respect to GND ............................................. -0.6V to VCC+0.5V Applied Voltage on A9 Pin with Respect to GND ............................................................ -0.6V to 13.5V Applied VPP Voltage with Respect to GND ......................................................................-0.6V to 13.5V Applied READ Voltage (Functionality is guaranteed between these limits) ................... +3V to +3.6V Note: These are stress ratings only. Stresses exceeding the range specified under "Absolute Maximum Ratings" may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
2
6th May '99
HT27LC512
D.C. Characteristics
Read operation
Symbol
VOH VOL VIH VIL ILI ILO ICC ISB1 ISB2 IPP
Parameter VCC
Output High Level Output Low Level Input High Level Input Low Level Input Leakage Current Output Leakage Current VCC Active Current Standby Current (CMOS) Standby Current (TTL)
Test Conditions Conditions
Min. Typ.
2.4 -- 2.0 -0.3 -5 -10 -- -- -- -- -- -- -- -- -- -- -- 1.0 -- --
Max.
-- 0.45 VCC+0.5 0.8 5 10 15 10 0.6 100
Unit
V V V V
A A
3.3V IOH=-0.4mA 3.3V IOL=2.0mA 3.3V 3.3V -- --
3.3V VIN=0 to 3.6V 3.3V VOUT=0 to 3.6V 3.3V CE=VIL, f=5MHz, IOUT=0mA
mA
A
3.3V CE=VCC0.3V 3.3V CE=VIH
mA
A
VPP Read/Standby Current 3.3V CE=OE=VIL, VPP=VCC
Programming operation
Symbol
VOH VOL VIH VIL ILI VH ICC IPP
Parameter
Output High Level Output Low Level Input High Level Input Low Level Input Load Current A9 Product ID Voltage VCC Supply Current VPP Supply Current
Test Conditions VCC Conditions
Min.
2.4 -- 0.7VCC -0.5 -- 11.5 -- --
Typ.
-- -- -- -- -- -- -- --
Max.
-- 0.45 VCC+0.5 0.8 5.0 12.5 40 10
Unit
V V V V
A
5.8V IOH=-0.4mA 5.8V IOL=2.1mA 5.8V 5.8V -- --
5.8V VIN=VIL, VIH 5.8V 5.8V 5.8V CE=VIL -- --
V mA mA
3
6th May '99
HT27LC512
Capacitance
Symbol
CIN COUT CVPP
Parameter VCC
Input Capacitance Output Capacitance VPP Capacitance 3.3V 3.3V 3.3V
Test Conditions Conditions
VIN=0V VOUT=0V VPP=0V
Min. Typ. Max. Unit
-- -- -- 8 8 18 12 12 25 pF pF pF
A.C. Characteristics
Read operation
Symbol
tACC tCE tOE tDF tOH
Parameter
Address to Output Delay Chip Enable to Output Delay Output Enable to Output Delay CE or OE High to Output Float, Whichever Occurred First
Test Conditions VCC Conditions
-120 Min.
-- -- -- -- 0
Unit Max.
120 120 45 40 -- ns ns ns ns ns
3.3V CE=OE=VIL 3.3V OE=VIL 3.3V CE=VIL 3.3V -- --
Output Hold from Address, CE or 3.3V OE, Whichever Occurred First
Programming operation
Ta=+25C5C
Symbol
tAS tOES tOEH tDS tAH tDH tDFP tPW tVCS tDV tVR
Parameter
Address Setup Time CE/VPP Setup Time OE/VPP Hold Time Data Setup Time Address Hold Time Data Hold Time Output Enable to Output Float Delay PGM Program Pulse Width VCC Setup Time Data Valid From CE OE/VPP Recovery Time
Test Conditions VCC
5.8V 5.8V 5.8V 5.8V 5.8V 5.8V 5.8V 5.8V 5.8V 5.8V 5.8V
Conditions
-- -- -- -- -- -- -- -- -- -- --
Min. Typ. Max. Unit
2 2 2 2 0 2 0 30 2 -- 2 -- -- -- -- -- -- -- 75 -- -- -- -- -- -- -- -- -- 130 105 -- 150 --
s s s s s s
ns
s s
ns
s
4
6th May '99
HT27LC512
Test waveforms and measurements
tR, tF< 20ns (10% to 90%)
Output test load
Note: CL=100pF including jig capacitance
Product Identification Code
Code A0
Manufacturer Device Type Continuation 0 1 0 1
Pins A1
1 1 0 0
DQ7
0 1 0 0
DQ6
0 0 1 1
DQ5
0 0 1 1
DQ4
1 0 1 1
DQ3
1 0 1 1
DQ2
1 0 1 1
DQ1
0 1 1 1
DQ0
0 1 1 1
Hex Data
1C 83 7F 7F
5
6th May '99
HT27LC512
Functional Description
Operation mode
All the operation modes are shown in the table following.
Mode
Read Output Disable Standby (TTL) Standby (CMOS) Program Program Verify Product Inhibit Manufacturer Code (3) Device Code (3) Notes: (1) VH = 12.0V 0.5V (2) X=Either VIH or VIL
CE
VIL VIL VIH VCC 0.3V VIL VIL VIH VIL VIL
OE/VPP
VIL VIH X X VPP VIL VPP VIL VIL
A0
X (2) X X X X X X VIL VIH
A9
X X X X X X X VH (1) VH (1)
Output
Dout High Z High Z High Z DIN DOUT High Z 1C 83
(3) For Manufacturer Code and Device Code, A1=VIH, When A1=VIL, both codes will read 7F
Programming of the HT27LC512
When the HT27LC512 is delivered, the chip has all 512K bits in the "ONE", or HIGH state. "ZEROs" are loaded into the HT27LC512 through the procedure of programming. The programming mode is entered when 12.20.2V is applied to the OE/VPP pin and CE is at VIL. For programming, the data to be programmed is applied with 8 bits in parallel to the data pins. The programming flowchart in Figure 3. shows the fast interactive programming algorithm. The interactive algorithm reduces programming time by using 30s to 105s programming pulses and giving each address only as many pulses as is necessary in order to reliably program the data. After each pulse is applied to a given address, the data in that address is verified. If the data is not verified, additional pulses are given until it is verified or until the maximum number of pulses is reached. This process is repeated while sequencing through each address of the HT27LC512. This part of the programming algorithm is carried at VCC=5.8V to
assure that each EPROM bit is programmed to a sufficiently high threshold voltage. This ensures that all bits have sufficient margin. After the final address is completed, the entire EPROM memory is read at VCC=VPP=5.250.25V to verify the entire memory.
Program inhibit mode
Programming of multiple HT27LC512 in parallel with different data is also easily accomplished by using the Program Inhibit Mode. Except for CE, all like inputs of the parallel HT27LC512 may be common. A TTL low-level program pulse applied to an HT27LC512 CE input with OE/VPP=12.20.2V will program that HT27LC512. A high-level CE input inhibits the other HT27LC512 from being programmed.
Program verify mode
Verification should be performed on the programmed bits to determine whether they were correctly programmed. The verification should be performed with OE/VPP and CE at VIL. Data should be verified at tDV after the falling edge of CE.
6 6th May '99
HT27LC512
Auto product identification
The Auto Product Identification mode allows the reading out of a binary code from an EPROM that will identify its manufacturer and type. This mode is intended for use by the programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm. This mode is functional in the 25C5C ambient temperature range that is required when programming the HT27LC512. To activate this mode, the programming equipment must force 12.00.5V on the address line A9 of the HT27LC512. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH, when A1=VIH. All other address lines must be held at VIH during Auto Product Identification mode. Byte 0 (A0=VIL) represents the manufacturer code, and byte 1 (A0=VIH), the device code. For HT27LC512, these two identifier bytes are shown in the Mode Select Table. All identifiers for the manufacturer and device codes will possess odd parity, with the MSB (DQ7) defined as the parity bit. When A1=VIL, the HT27LC512 will read out the binary code of 7F, continuation code, to signify the unavailability of manufacturer ID codes.
Read mode
standby mode which reduces the maximum VCC current to 0.6mA. It is placed in TTLstandby when CE is at VIH. When in standby mode, the outputs are in a high-impedance state, independent of the OE input.
Two-line output control function
To accommodate multiple memory connections, a two-line control function is provided to allow for:
* Low memory power consumption * Assurance that output bus contention will not
occur. It is recommended that CE be decoded and used as the primary device-selection function, while OE be made a common connection to all devices in the array and connected to the READ line from the system control bus. This assures that all deselected memory devices are in their lowpower standby mode and that the output pins are only active when data is desired from a particular memory device.
System considerations
The HT27LC512 has two control functions, both of which must be logically satisfied in order to obtain data at outputs. Chip Enable (CE) is the power control and should be used for device selection. Output Enable (OE) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that addresses are stable, address access time (tACC) is equal to the delay from CE to output (tCE). Data is available at the outputs (tOE) after the falling edge of OE, assuming the CE has been LOW and addresses have been stable for at least tACC-tOE.
Standby mode
During the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading of the device. At a minimum, a 0.1F ceramic capacitor (high frequency, low inherent inductance) should be used on each device between VCC and VPP to minimize transient effects. In addition, to overcome the voltage drop caused by the inductive effects of the printed circuit board traces on EPROM arrays, a 4.7F bulk electrolytic capacitor should be used between VCC and VPP for each eight devices. The location of the capacitor should be close to where the power supply is connected to the array.
The HT27LC512 has CMOS standby mode which reduces the maximum VCC current to 10A. It is placed in CMOS standby when CE is at VCC0.3V. The HT27LC512 also has a TTL-
7
6th May '99
HT27LC512
Figure 1. A.C. waveforms for read operation
Figure 2. Programming waveforms
8
6th May '99
HT27LC512
Figure 3. Fast programming flowchart
9
6th May '99
HT27LC512
Holtek Semiconductor Inc. (Headquarters) No.3 Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Tel: 886-3-563-1999 Fax: 886-3-563-1189 Holtek Semiconductor Inc. (Taipei Office) 5F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan, R.O.C. Tel: 886-2-2782-9635 Fax: 886-2-2782-9636 Fax: 886-2-2782-7128 (International sales hotline) Holtek Microelectronics Enterprises Ltd. RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong Tel: 852-2-745-8288 Fax: 852-2-742-8657 Copyright (c) 1999 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw.
10
6th May '99

▲Up To Search▲

Price & Availability of HT27LC512

	To Download HT27LC512 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .